1. Home
  2. >Recommend
  3. >5052 Aluminum Alloy | Sheet, Plate, Bar, Tube & Coil

5052 Aluminum Alloy | Sheet, Plate, Bar, Tube & Coil

Notice: Production MOQ 500 kg. China-based stock available for project procurement and bulk orders.

5052 is a non-heat-treatable aluminum-magnesium alloy with good formability, weldability, and corrosion resistance.

5052 aluminum sheet is widely used for sheet metal enclosures, formed components, and marine equipment. 5052-H32 aluminum is a common sheet temper that balances strength, formability, and corrosion resistance.

5052 aluminum plate and sheet product image

Henan Chalco can coordinate sourcing and custom quotations for 5052 sheet, plate, bar, tube, and coil based on the required temper, including H32, O, or H34, as well as thickness, dimensions, tolerances, and material standards.

  • Alloy System: Al–Mg; non-heat-treatable
  • Magnesium Content: 2.2–2.8%
  • Nominal Density: approx. 2.68 g/cm³
  • temper: O / H32 / H34

5052 Aluminum Products

5052 aluminum is available in various product forms, including sheet, plate, coil, strip, bar, block, tube, wire, foil, and honeycomb core. Cut-to-size parts, formed components, surface finishes, and custom assemblies can also be assessed against drawings.

Henan Chalco coordinates product sourcing based on form, temper, specifications, and acceptance requirements.

5052 Aluminum Sheet & Plate

Suitable for equipment enclosures, bent sheet metal parts, and marine covers. Material can be selected by thickness, temper, and dimensions to balance formability, weldability, and corrosion resistance.

contact us
5052 h32 aluminum sheets and plates for sheet metal fabrication
5052 aluminum round bars and rods for machining

5052 Aluminum Bar & Rod

Suitable for turning, milling, and custom mechanical parts. Select round or square bar stock by cross-section, temper, dimensions, and machining allowance.

contact us

5052 Aluminum Tube & Pipe

Suitable for industrial tube fittings, bent tube sections, and welded tubular assemblies. Round, square, and rectangular tubing can be evaluated by dimensions, wall thickness, and manufacturing method.

contact us
5052 aluminum round and square tubes
5052 aluminum coils and slit strips

5052 Aluminum Coil & Strip

Suitable for progressive stamping, roll forming, and precision slitting. Choose coil or strip based on thickness, width, temper, and winding requirements.

contact us

5052 Aluminum Sheet, Plate & Flat Products

5052 sheet, plate, and other flat products offer good formability, weldability, and corrosion resistance for sheet metal fabrication, precision cutting, and custom parts. Material selection can be tailored to the required thickness, temper, dimensions, and surface finish.

5052 sheet and plate can be selected by temper, thickness, and sheet dimensions. 5052-H32 is one of the most commonly used tempers for sheet metal fabrication and general industrial applications.

Temper Thickness Examples Selection Guide
5052-H32 0.020 / 0.032 / 0.040 / 0.063 / 0.125 / 0.190 / 0.250 / 0.375 / 0.500 in For sheet applications requiring a balance of strength, bend formability, and corrosion resistance.
5052-O 0.025 / 0.032 / 0.040 in For bending, stamping, and deep drawing that require substantial deformation.
5052-H34 0.032 in For higher-strength sheet applications involving relatively limited forming.
5052-H112 Some market listings include thicknesses over 0.500 in For evaluating machining and welding applications involving thicker plate.

Common Sheet Dimensions: Common market-listed sheet widths include 36", 48", and 60", with lengths of 96", 120", and 144".

We can coordinate a review of available sizes and supply feasibility based on the required thickness × width × length, temper, tolerances, and cutting drawings.

5052 Aluminum Bar, Rod & Block

5052 aluminum bar and block offer good corrosion resistance and suitability for certain machining operations. They are used for mechanical parts, custom structural components, and CNC machining blanks. Choose the appropriate stock based on cross-section, size, temper, and machining accuracy requirements.

5052 Aluminum Tube, Pipe & Hollow Stock

5052 aluminum tubing offers good corrosion resistance, formability, and weldability for industrial pipe components, bent tube assemblies, and equipment structures. Custom options can be assessed for round, square, or rectangular profiles, dimensions, wall thickness, and precision requirements.

For aerospace tubing, see 5052 Aerospace Aluminum Tube.

5052 Aluminum Coil & Strip

5052 aluminum coil and strip offer good formability, weldability, and corrosion resistance for progressive stamping, roll forming, and precision slitting. Select material based on thickness, width, temper, slitting tolerances, and coil requirements.

5052 Aluminum Wire & Wire Rod

5052 aluminum wire and wire rod offer good corrosion resistance and formability for rivets, cold-headed fasteners, and custom formed parts. Custom specifications can be assessed based on wire diameter, temper, winding format, and downstream processing requirements.

5052 Aluminum Foil & Fin Stock

5052 aluminum foil and fin stock offer good corrosion resistance and formability for aluminum honeycomb cores, heat exchanger fins, and lightweight industrial components. Custom options can be evaluated by foil thickness, width, temper, and surface treatment requirements.

5052 Aluminum Honeycomb & Sandwich Materials

5052 aluminum honeycomb core combines low weight, good corrosion resistance, and high specific stiffness. It is used in aerospace interiors, industrial equipment panels, and lightweight sandwich structures. Custom configurations can be evaluated by cell size, foil thickness, core thickness, density, and sandwich construction requirements.

Custom 5052 Aluminum Parts & Special Projects

For nonstandard parts and special assemblies, manufacturing and supply feasibility can be assessed against the required temper, drawings, processes, and inspection criteria.

  • 5052 Laser-Cut / Waterjet-Cut Parts: Sheet components, complex profiles, and precision blanks cut to drawing.
  • 5052 Stamped / Punched Components: Stamped parts, perforated components, bent brackets, mounting parts, and formed components.
  • 5052 CNC-Machined Parts: Parts machined from sheet, bar, or block, with machining allowances and tolerances checked against drawings.
  • 5052 Rings / Washers / Annular Blanks: Rings, washers, and circular blanks with center holes.
  • 5052 Anodized / Powder-Coated Components: Custom parts finished by anodizing, powder coating, or other specified surface treatments.
  • 5052 Formed Roofing / Deck Profiles: Special roll-formed sheets, roofing panels, or B-Deck profiles. Alloy suitability, cross-section, and manufacturing method require prior assessment.
  • 5052 Special Angles / Profiles & Joined Assemblies: Drawings may be submitted for angles, special profiles, or assemblies joined to other materials. Alloy suitability, manufacturing methods, and joint verification require separate evaluation.
  • 5052 Foil-Faced PMI Sandwich Components: Special sandwich structures using ultrathin 5052 foil and a PMI core. Bonding and surface pretreatment requirements can be submitted for an engineering feasibility review.

Available tempers, dimensional combinations, processing methods, and supply scope for special products are subject to confirmation against the drawings and order requirements.

5052 Aluminum Tempers and Selection Guide

5052 is a non-heat-treatable aluminum alloy commonly specified in tempers such as O, H32, H34, and H38.

5052-H32 is a common choice for sheet, plate, coil, and strip where strength, formability, and corrosion resistance need to be balanced.

Temper Material Characteristics Selection Guidance
5052-O Annealed; high ductility and lower strength Deep-drawn parts, complex bends, and other heavily formed components
5052-H32 Strain-hardened and stabilized; quarter-hard Sheet metal, enclosures, and industrial sheet requiring both strength and formability
5052-H34 Strain-hardened and stabilized; half-hard Sheet and strip requiring higher strength with limited forming
5052-H38 Strain-hardened and stabilized; full-hard Sheet and strip requiring greater strength and hardness with minimal forming
5052-H112 Temper with specified mechanical properties after forming or processing Sheet, plate, and machining stock evaluated under the applicable product standard
5052-H114 Special temper associated with embossed or raised-pattern sheet and plate Tread and embossed plate covered by the applicable specification

For complex bends or deep drawing, consider 5052-O first;

for general sheet metal fabrication requiring both strength and formability, evaluate 5052-H32;

for sheet products requiring higher strength with less forming, compare H34 and H38.

5052 Aluminum Chemical Composition

Magnesium (Mg) is the principal alloying element in 5052 aluminum, with a smaller addition of chromium (Cr).

Element Chemical Composition (wt. %)
Magnesium (Mg) 2.2–2.8
Chromium (Cr) 0.15–0.35
Silicon (Si) ≤0.25
Iron (Fe) ≤0.40
Copper (Cu) ≤0.10
Manganese (Mn) ≤0.10
Zinc (Zn) ≤0.10
Other Elements (Each) ≤0.05
Other Elements (Total) ≤0.15
Aluminum (Al) Balance

Source: The Aluminum Association, Teal Sheets, December 2025 revision, page 9 (registered composition for 5052).

5052 Aluminum Physical Properties

Physical Property Value
Density 2.68 g/cm³
Young's Modulus (Tensile) 69.3 GPa
Poisson's Ratio 0.33
Thermal Conductivity 138 W/(m·K)
Coefficient of Thermal Expansion 23.8 × 10⁻⁶/K
Electrical Conductivity approx. 35% IACS

5052 Aluminum Mechanical Properties by Temper

The table lists typical mechanical properties for different 5052 tempers to compare strength, hardness, and formability.

Temper Tensile Strength (MPa) Yield Strength (MPa) Elongation (%) Brinell Hardness (HB)
5052-O 195 90 25 47
5052-H32 230 195 12 60
5052-H34 260 215 10 68
5052-H38 290 255 7 77

Source: ASM Handbook, Volume 2, Table 58. Values are typical reference properties; elongation corresponds to specimens approximately 1.6 mm thick, and Brinell hardness follows the test conditions specified in the source table.

5052 Aluminum Applications

Sheet Metal Enclosures & Signs

5052 sheet and coil are used for equipment enclosures, cabinet covers, and road signs. Bending, punching, and surface treatment can help meet different fabrication requirements.

5052 aluminum enclosures and signs
5052 aluminum marine components

Marine & Coastal Equipment

5052 sheet, tread plate, and coil provide good resistance to atmospheric corrosion and can be used for marine covers, interior vessel components, and coastal equipment panels, subject to the actual exposure conditions.

Welded Tanks & Fluid Lines

5052 sheet, plate, and tubing can be considered for fuel tanks, liquid storage tanks, and fluid lines, subject to the medium, welded joint design, and leak-tightness requirements.

Welded aluminum tanks and pipes
Machined aluminum parts and tubes

Machined Parts & Tubular Components

5052 bar, block, and round, square, or rectangular tubing can be used to produce machined parts and tubular components to drawing.

Lightweight Honeycomb Structures

5052 honeycomb core can be used in lightweight sandwich structures and equipment panels. Final structural performance depends on core specifications, face sheets, and bonded-joint design.

5052 aluminum honeycomb core panels

Fabrication Considerations

Bending & Stamping

5052-O is better suited to substantial forming, while bending 5052-H32 and H34 requires consideration of sheet thickness. For example, for a 90° cold bend in 3.18 mm sheet, the recommended minimum inside bend radii are approximately 1.5t (4.8 mm) for H32 and 2t (6.4 mm) for H34. Trial bends should be used to confirm the actual forming conditions.

Welding

5052 can be MIG- or TIG-welded, and ER5356 is one commonly considered filler metal. However, welding H-temper material can soften the heat-affected zone. Filler selection and joint performance must be verified against the service requirements.

Cutting & Machining

5052 sheet, bar, and block can be cut, punched, and machined. Drawings should specify cut-edge quality, burr limits, flatness, and critical dimensional tolerances.

Anodizing & Coating

5052 can be anodized or coated, although thicker anodic films may develop a yellowish tint. For parts with strict appearance requirements, the finish should be agreed against an approved sample before production.

Aluminum bending, welding, CNC machining and surface finishing

Common Standards for 5052 Aluminum

Product Form Reference Standard
Sheet / Plate / Coil / Strip ASTM B209/B209M-21a; GB/T 3880.1-2023, GB/T 3880.2-2024, GB/T 3880.3-2024; EN 485 series
Bar / Rod / Cold-Finished Wire ASTM B211/B211M-23
Drawn Seamless Tube / Coiled Tubing ASTM B210/B210M-26
Rolled Tread Plate ASTM B632/B632M-24
Rivet / Cold-Heading Wire & Rod ASTM B316/B316M-25
Aluminum Foil GB/T 3198-2020
Aluminum Honeycomb Core SAE AMS-C-7438A
Custom Fabricated Components Applicable raw material standard + customer drawings and purchase requirements

AMS Specifications for 5052-O, H32, and H34 Sheet and Plate:

5052 Temper SAE Specification Nominal Thickness Range in the Specification
5052-O AMS4015N 0.15–76.20 mm
5052-H32 AMS4016N 0.43–50.80 mm
5052-H34 AMS4017M 0.23–25.40 mm

Quality Inspection and Material Certificates

Depending on the product standard and purchase order, quality inspection for 5052 aluminum may include:

  • Chemical Composition: Alloying element analysis and material batch verification.
  • Mechanical Properties: Testing as required for tensile strength, yield strength, elongation, and other applicable properties.
  • Dimensions & Surface: Checks of thickness, width, flatness, dimensional tolerances, and surface quality.
  • Special Inspection: Additional inspection of tubing, honeycomb core, or custom parts as required by the application.
  • Traceability & Documents: Material identification, batch traceability, and relevant inspection records.

Material Certificates: An MTC is not automatically equivalent to an EN 10204 Type 3.1 certificate. If Type 3.1, Type 3.2, SGS, or other third-party inspection is required, specify the document type, inspection scope, and issuing party when requesting a quotation. Arrangements are subject to order confirmation.

Instant Quote

5052 vs 6061 Aluminum: Selection Overview

5052 is generally considered for sheet applications requiring bending, welding, and corrosion resistance. 6061-T6/T651 is more commonly considered for parts requiring higher strength and good machinability.

Selection Factor 5052 Aluminum 6061 Aluminum
Strength & Temper Non-heat-treatable alloy, commonly supplied in O, H32, and H34 tempers; suitable where strength and formability must be balanced. Heat-treatable alloy; T6/T651 tempers generally offer higher strength.
Bending & Forming O and H32 sheet can be considered for bending, stamping, and sheet metal forming. O and T4 tempers can be formed; tighter bends are more restricted in the T6 condition.
Corrosion & Welding More commonly considered for formed or welded sheet components; machinability should be evaluated for extensive cutting operations. 6061-T6/T651 is commonly considered for parts requiring strength and machinability; the specified temper must match the product form.
CNC Machining Machinable, although chip control and machining efficiency should be assessed for extensive material removal. T6/T651 tempers are generally better suited to milling, drilling, and precision machined parts.

For bent enclosures, stamped sheet metal parts, and covers exposed to coastal atmospheres, evaluate 5052 first;

for higher-strength components or parts involving extensive CNC machining, compare 6061-T6/T651.

Read the full 5052 vs 6061 Aluminum comparison.

Related Aluminum Products

For projects with different forming, strength, corrosion resistance, or machining requirements, consider the following alternative aluminum alloy products.

Frequently Asked Questions About 5052 Aluminum

Can 5052 aluminum be heat treated to T6?

No. 5052 is a non-heat-treatable aluminum alloy. Common tempers include O, H32, and H34; it is not normally specified in the T6 condition.

Can 5052 aluminum be welded to 6061?

Yes, joining these alloys by an appropriate welding process can be considered. Filler metal, service conditions, and joint design must be evaluated, including properties in the heat-affected zone after welding.

How do I calculate the weight of 5052 aluminum sheet?

Estimate the weight using the nominal density of 2.68 g/cm³:

Weight (kg) ≈ length (mm) × width (mm) × thickness (mm) × 0.00000268.

The actual delivered weight depends on dimensions and measured weight.

What are the equivalent designations for 5052 aluminum?

Common designations include AA 5052, UNS A95052, EN AW-5052 (AlMg2.5), and JIS A5052. Always confirm the applicable product standard, temper, and mechanical property requirements; similar alloys should not automatically be treated as equivalent.

Can 5052 aluminum be extruded into custom profiles?

5052 can be extruded, but it is less commonly used for profiles than 6063. Custom cross-sections require a separate assessment of manufacturing and supply feasibility. Provide a profile drawing, dimensions, tolerances, and order quantity for evaluation.

Custom 5052 Aluminum Supply and Quotation

Henan Chalco coordinates sourcing for 5052 sheet, plate, bar, tube, coil, strip, wire, honeycomb core, and custom parts. Temper, dimensions, finishes, and processing options can be assessed against project requirements.

Please include the following information in your inquiry:

  • Material & Specifications: Product form, temper, dimensions, and tolerances.
  • Customization: Cutting, slitting, punching, CNC machining, surface finishing, or fabrication drawings.
  • Quantity & Quality: Order quantity, material standards, and required inspection documents.
  • Delivery: Destination, trade terms, and requested delivery date.

Specific available sizes, processing options, MOQ, lead times, and inspection documents are subject to order confirmation.

Chalco can provide you the most comprehensive inventory of aluminum products and can also supply you customized products. Precise quotation will be provided within 24 hours.

Get a quote
Do you have the aluminum you need?

Welcome to contact us

  • Alloy, temper, size, and quantity review
  • Drawing, sample, and standard support
  • Available materials and integrated project supply
  • Product demand
  • Name
  • Phone number or WhatsApp
  • Email
  • content

Production MOQ 500 kg. Integrated supply for projects and volume orders.